- Sensor Wiring Intermittent Connection Error Code 14 See User Manual 2016
- Sensor Wiring Intermittent Connection Error Code 14 See User Manual Online
- Sensor Wiring Intermittent Connection Error Code 14 See User Manual Iphone
- Sensor Wiring Intermittent Connection Error Code 14 See User Manual Video
- Sensor Wiring Intermittent Connection Error Code 14 See User Manual Guide
- Sensor Wiring Intermittent Connection Error Code 14 See User Manual Pdf
page
Rinnai Tankless Water Heater Troubleshooting Manual WARNING There are a number of live tests that are required when fault finding this product. Extreme care should be used at all times to avoid contact with energized components inside the furnace. INSTALLATION AND MAINTENANCE INSTRUCTIONS. FOR MODEL 2300TB. Before installing detectors, please thoroughly read System Sensor Manual I56-407-XX, Guide for Proper Use of System Smoke Detectors, which provides detailed information on detector spacing, placement, zoning, wiring, and special applications. Nov 18, 2015 If I understand correctly, you have a new battery, but now the engine does not start? P0339 refers to the crank position sensor circuit having an intermittent connection, which wouldn’t be related to the battery in any way. The only thing I can think of is that the connector may be loose or the wire to the sensor may have a break.
48
Banner Engineering Corp.
•
Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Troubleshooting and Maintenance
EZ-SCREEN Grid
Instruction Manual
Diagnostic
Display
Error
Description
Test Input Error
This error can occur if excessive noise is
present on the test input.
Emitter Error
This error can occur either due to
excessive electrical noise or due to an
internal failure.
Excessive Noise Error
This error can occur due to excessive
electrical noise.
• Reset the emitter by disconnecting and reapplying power to the emitter (see
Section 4.2).
• If the error clears, perform a Daily Checkout procedure (Section 6.4) and if
OK, resume operation. If the system fails the Daily Checkout procedure, replace
the emitter.
• If the error continues, check the ground connection (terminal 1).
• If the sensor has a good earth ground connection to terminal 1, check for
noise on the test input wiring (see Sections 5.2 and 5.3).
• Reset the emitter by disconnecting and reapplying power to the emitter (see
Section 4.2).
• If the error clears, perform a Daily Checkout procedure (Section 6.4) and if
Sensor Wiring Intermittent Connection Error Code 14 See User Manual 2016
OK, resume operation. If the system fails the Daily Checkout procedure, replace
the emitter.
• If the error continues, check the ground connection (terminal 1).
• If the sensor has a good earth ground connection to terminal 1, check for
electrical noise (see Section 5.2).
• If the error continues, replace the emitter.
• Reset the emitter by disconnecting and reapplying power to the emitter (see
Section 4.2).
• If the error clears, perform a Daily Checkout procedure (Section 6.4) and if
OK, resume operation. If the system fails the Daily Checkout procedure, replace
the emitter.
• If the error continues, check the ground connection (terminal 1).
• If the sensor has a good earth ground connection to terminal 1, check for
electrical noise (see Section 5.2).
• If the error continues, replace the emitter.
5.1.2 Emitter Error Codes
NOTE: The emitter flashes the number 2 followed by the other error code digit, pauses, then flashes the sequence again.
Figure 5-2. Emitter error codes
Cause of Error
Sensor Wiring Intermittent Connection Error Code 14 See User Manual Online
INSTALLATION AND MAINTENANCE INSTRUCTIONS
Sensor Wiring Intermittent Connection Error Code 14 See User Manual Iphone
FOR MODEL 2300TB
Before installing detectors, please thoroughly read System Sensor Manual I56-407-XX, Guide for Proper Use of System Smoke
Detectors, which provides detailed information on detector spacing, placement, zoning, wiring, and special applications. Copies
of this manual are available at no charge from System Sensor.
GENERAL DESCRIPTION:
Model 2300TB is a 2-wire combination smoke/heat detector. In addition to photoelectronic smoke detection, two supervised
electronic thermistors provide restorable 135°F fixed temperature heat detection. The installation is simplified by the use of an
adaptor bracket and a plug-in screw terminal block which can be pre-wired to the system allowing the detector to be easily
installed or removed for cleaning. It is designed to provide open area protection, and to be used with UL listed compatible 2-
wire control panels. The detector’s sensitivity can be tested in place using the MOD400R field sensitivity test module.
The 2300TB is listed to UL 268 and is a latching type system detector. When latched in alarm, the detector must be reset by
a momentary power interruption.
An LED on the detector provides a local indication of the detector’s status. If power is applied to the detector, and the detector
is functioning properly in standby, the status LED will blink every 10 seconds. The detector performs a self-test on its smoke
sensing chamber and internal electronics every 40 seconds. If this test fails, the detector stops blinking the status LED in
standby, and the LED will remain off. In alarm, the LED will be latched on continuously until the detector is reset.
The detector provides an output for connection to an optional Remote Annunciator (model RA400Z). The Remote Annunciator
mounts to a single gang box and provides an LED indication of an alarm condition.
SPECIFICATIONS:
Diameter: 5.5 inches (14 cm)
Height: 2.5 inches (64 mm)
Weight: 0.7 lb (310 gm)
Operating Temperature Range: 0° to +38° C (32° to 100° F)
Operating Humidity Range: 10% to 90% Relative Humidity Non-condensing
Latching Alarm: Reset by momentary power interruption.
Test Feature: Recessed test switch.
Maximum Air Velocity: 3000 Ft./Min. (15 Meters/Sec.).
Sensitivity: Nominal 3%/Ft.
Heat Sensor: 135°F Fixed Temperature Electronic Thermistor
ELECTRICAL RATINGS:
System Voltage nominal: 12 or 24 VDC
minimum: 8.5 VDC
maximum: 35 VDC
Maximum Ripple Voltage: 30% of nom. Voltage (peak to peak)
Start-up Capacitance: 0.02 µF maximum
Standby Current: 120 µA maximum
Alarm Ratings: 4.2 VDC minimum at 10 mA.
6.6 VDC maximum at 100 mA.
Alarm current must be limited to 100 mA maximum by the
control panel. If used, the RA400Z Remote Annunciator
operates within the specified detector alarm currents.
Reset Voltage: 2.5 VDC minimum
Reset Time: .3 Sec. maximum
Start-up Time: 34 Sec. maximum
(After 60 Sec. Reset)
D300-01-00 I56-490-05
System Sensor, 3825 Ohio Avenue, St. Charles, Illinois 60174, 1-800-SENSOR2, FAX 708-377-6495
S0181-00
Sensor Wiring Intermittent Connection Error Code 14 See User Manual Video
Figure 1. 2300TB Smoke/Heat Detector