a) Front C.I.L assembled to 14” Diffuser (1pc)

b) Rear C.I.L. assembled to 14” Diffuser (1pc)

c) 120V AC Adapter, Output: 12V DC@500mA (1pcs)

d) 9.25” Wire-Rods (4pcs)

e) 6.5” Wire-Rods with brass connectors (4pcs)

f) 4FT Power Connection Cord

Optional:

g) AutoStarter Battery Pack ( See Fig. 2 ).

SET UP THE CHRONY INFRARED LIGHT with a 120V AC Adapters:

Step1: Follow the “Quick Set-up Instructions” on the manual of your Chrony Model until completion of Wire-Rod set up.

Step2: Install the Front C.I.L. (a) into the front Wire-Rods of the Chrony and install the Rear C.I.L. (b) into the rear Wire-Rods of the Chrony. Make sure the Green and Red LEDs inside the C.I.L. housings are facing towards the front (The Main Power Jacks will be on the left side, see Fig. 1).

Step3: Plug 4FT Power Connection Cord (f) to each front and rear Power Connection Jacks of the C.I.L.

Step4: Connect the jack plug of 120V AC Adapter (c) to the main power jack of the front C.I.L. (a), and then plug the adapter into a standard electrical outlet. When the green LEDs on the C.I.L. appear, it’s READY to use. If the red LED appears, this indicates a bad connection or power status (low battery, input Voltage is lower than 12V DC, or the Current is lower than 400mA).

Note: If the front and rear C.I.L. are installed in reverse, the velocity accuracy will be affected.

SET UP THE CHRONY INFRARED LIGHT with an AutoStarter Battery Pack:
The AutoStarter does not come fully charged from the factory. It is necessary to charge the unit before initial use. Refer to “Recharging the AutoStarter” portion of the AutoStarter manual.

The “ Function Button” of the AutoStarter has two positions IN and OUT. The “IN” position is OFF and the “OUT” position is ON. When the unit is shipped from the factory, it should be in the “IN” position. (See Figure # 3)

Figure 2: AutoStarter Battery Pack (g)

Figure 3: AutoStarter Battery Functions

1. Follow the Step1 to Step3 above.
   
2. Connecting to the AutoStarter Battery (g). Make sure it is on the “OFF” position:
   a) Plug the separate socket cord into the 12V DC Socket of the AutoStarter and connect the end plug into the main power jack of the front C.I.L.
   b) Press the function button of the AutoStarter to the “ON” position. The “VL” light should appear GREEN. Discontinue use and recharge the AutoStarter once the “VL” light turns red.
   
3. When the Green Lights of the LED appear on both front and rear C.I.L., it is READY to use. If any RED light appears on the C.I.L., the unit is NOT READY to use. In this case, (1) Check all the cable connections making sure all jack plugs are all the way in. (2) Check the “VL” light on the AutoStarter if it is turning RED then the AutoStarter needs to be recharged.

STORING AND PRECAUTIONS

• NEVER operate the Chrony Chronograph and the Chrony Infrared Light under RAINING conditions.
• NEVER use an AC Adapter that indicates more or less than 12VDC output.
• DO NOT reverse the front and rear C.I.L.
• DO NOT connect the separate socket cord directly to the car cigarette lighter socket to power the
  C.I.L
• DO NOT store the unit in temperature less than 14°F ( -10°C ) or higher than 120°F ( -50°C ).
• In case the unit has been shot, DO NOT TOUCH any metal parts! TURN OFF the Power Source immediately.
• For AutoStarter: Refer to the AutoStarter Manual for Storing and Precautions.

USA: 3840 E Robinson Rd. PMB# 298, Amherst, NY 14228

Canada: 2446 Cawthra Rd., Bldg.# 1, Unit# 10
Mississauga, Ontario L5A 3K6

• To Order Call: 1-800-385-3161 or (905) 276-6292 (9am-5pm E.S.T)
• Fax: (905) 276-6295 ·Email: chrony@shootingchrony.com
• Website: www.shootingchrony.com